CC BY
99
Yb:CALYO-based femtosecond chirped pulse regenerative amplifier for temporally resolved pump-probe spectroscopy
Alexander Rudenkov1, Viktor Kisel1, Anatol Yasukevich1, Karine Hovhannesyan2, Ashot Petrosyan2, Nikolai Kuleshov1
Center for Optical Materials and Technologies, Belarusian National Technical University, Nezavisimosty Ave., 65, Minsk 220013, Belarus
2Institute for Physical Research, National Academy of Sciences of Armenia, 0203, Ashtarak-2, Armenia
Received 25.06.2018
Accepted for publication 28.07.2018
Abstract
Diode-pumped femtosecond chirped pulse regenerative amplifiers based on Yb3+-materials are of practical importance for wide range of scientific, industrial and biomedical applications. The aim of this work was to study the amplification of broadband chirped femtosecond pulses in regenerative amplifier based on Yb3+:CaYAlO4 crystal.
Such systems use femtosecond mode-locked lasers as seed pulse sources and amplify nJ-seed pulses to sub-mJ energy range. Most chirped pulse regenerative amplifier systems described in the literature use seed lasers with typical pulse spectral width at the level of 10-15 nm full width at half maximum (FWHM) that limit the seed pulse duration of about 90 fs and amplified pulse duration at the level of 200 fs due to strong influence of gain narrowing effect on the amplified pulse parameters. Yb3+-doped crystals with wide and smooth gain bandwidth as an active medium of chirped femtosecond pulse regenerative amplification systems allow to reduce negative contribution of gain narrowing effect and lead to shortening of amplified pulses. In this research we study the chirped pulse regenerative amplification of broad-band femtosecond pulses (60 nm spectral width FWHM) in the Yb3+:CaYAlO4-based chirped pulse regenerative amplifier. Substantial reduction of the amplified pulse duration down to 120 fs (19.4 nm spectral width FWHM) with average power of 3 W at 200 kHz pulse repetition frequency was demonstrated without any gain narrowing compensation technique.
The results of experimental investigation of broad-band seeded Yb3+:CaYAlO4-based chirped pulse regenerative amplifier are reported for the first time to our knowledge. 120 fs-pulses (19.4 nm FWHM) with average output power of 3 W were demonstrated without any gain narrowing compensation technique. Despite the significant reduction of amplified pulse duration the task of improvement group velocity dispersion balance (including high orders of group velocity dispersion) remains relevant.
Keywords: broad-band chirped pulses, chirped pulse amplifier, regenerative amplifier, spectral broadening, DOI: 10.21122/2220-9506-2018-9-3-205-214
Адрес для переписки:
Руденков А.С.
Центр оптических материалов и технологий, Белорусский национальный технический университет, пр-т Независимости, 65, г. Минск 220013, Беларусь e-mail: [email protected]
Для цитирования:
Alexander Rudenkov, Viktor Kisel, Anatol Yasukevich,
Karine Hovhannesyan, Ashot Petrosyan, Nikolai Kuleshov.
Yb:CALYO-based femtosecond chirped pulse regenerative amplifier
for temporally resolved pump-probe spectroscopy.
Приборы и методы измерений.
2018. - Т. 9, № 3. - С. 205-214.
DOI: 10.21122/2220-9506-2018-9-3-205-214
Address for correspondence:
Alexander Rudenkov
Center for Optical Materials and Technologies, Belarusian National Technical University,
Nezavisimosty Ave., 65, Minsk 220013, Belarus e-mail: [email protected]
For citation:
Alexander Rudenkov, Viktor Kisel, Anatol Yasukevich,
Karine Hovhannesyan, Ashot Petrosyan, Nikolai Kuleshov.
Yb:CALYO-based femtosecond chirped pulse regenerative amplifier
for temporally resolved pump-probe spectroscopy.
Devices and Methods of Measurements.
2018, vol. 9, no. 3, pp. 205-214.
DOI: 10.21122/2220-9506-2018-9-3-205-214
Alexander Rudenkov et al.
УДК 621.373.826
Регенеративный усилитель чирпированных фемтосекундных импульсов на основе кристалла Yb:CALYO для спектроскопии возбуждения-зондирования с высоким временным разрешением
Руденков А.С.1, Кисель В.Э.1, Ясюкевич А.С.1, Ованесьян К.Л.2, Петросян А.Г.2, Кулешов Н.В.1
'Центр оптических материалов и технологий, Белорусский национальный технический университет, пр-т Независимости, 65, г. Минск 220013, Беларусь
2Институт физических исследований Национальной академии наук Армении, 0203, Аштарак-2, Армения
Поступила 25.06.2018 Принята к печати 28.07.2018
Регенеративные усилители чирпированных фемтосекундных импульсов на основе материалов с ионами Yb3+ с диодной накачкой нашли широкое применение в различных отраслях науки, производства и медицины. Целью данной работы являлось исследование режима регенеративного усиления широкополосных чирпированных фемтосекундных импульсов в усилителе на основе кристалла Yb3+:CaYAЮ4.
Используя в качестве задающего генератора лазер с пассивной синхронизацией мод, данные системы усиливают импульсы наноджоулевого диапазона энергий до суб-милиджоулевого уровня благодаря методике усиления чирпированных импульсов. Большинство описанных в литературе систем усиления используют задающие генераторы, обеспечивающие фемтосекундные импульсы со спектральной полушириной в диапазоне 10-15 нм, что ограничивает минимальную длительность задающих импульсов на уровне 90 фс. В процессе регенеративного усиления длительность усиленных импульсов увеличивается до значений около 200 фс, что связано с сильным негативным влиянием эффекта сужения спектра импульса под воздействием полосы усиления активной среды усилителя. Применение кристаллов, имеющих широкие и гладкие полосы усиления в качестве активных сред систем усиления чирпиро-ванных фемтосекундных импульсов широкого спектрального диапазона, позволяет снизить негативный вклад эффекта сужения спектра импульса и приводит к сокращению длительности усиленных импульсов.
В работе впервые представлены результаты исследования режима регенеративного усиления широкополосных чирпированных фемтосекундных импульсов в усилителе на основе кристалла Yb3+:CaYAЮ4. Получены импульсы длительностью 120 фс (спектральная полуширина 19,4 нм) со средней выходной мощностью системы усиления 3 Вт без применения методик компенсации эффекта сужения спектра усиливаемого импульса.
Ключевые слова: чирпированные импульсы широкого спектрального диапазона, усилитель чирпированных импульсов, регенеративный усилитель, расширение спектра импульса, эффект сужения спектра импульса.
DOI: 10.21122/2220-9506-2018-9-3-205-214
Адрес для переписки:
Руденков А.С.
Центр оптических материалов и технологий, Белорусский национальный технический университет, пр-т Независимости, 65, г. Минск 220013, Беларусь e-mail: [email protected]
Address for correspondence:
Alexander Rudenkov
Center for Optical Materials and Technologies, Belarusian National Technical University,
Nezavisimosty Ave., 65, Minsk 220013, Belarus e-mail: [email protected]
Для цитирования:
Alexander Rudenkov, Viktor Kisel, Anatol Yasukevich,
Karine Hovhannesyan, Ashot Petrosyan, Nikolai Kuleshov.
Yb:CALYO-based femtosecond chirped pulse regenerative amplifier
for temporally resolved pump-probe spectroscopy.
Приборы и методы измерений.
2018. - Т. 9, № 3. - С. 205-214.
DOI: 10.21122/2220-9506-2018-9-3-205-214
For citation:
Alexander Rudenkov, Viktor Kisel, Anatol Yasukevich,
Karine Hovhannesyan, Ashot Petrosyan, Nikolai Kuleshov.
Yb:CALYO-based femtosecond chirped pulse regenerative amplifier
for temporally resolved pump-probe spectroscopy.
Devices and Methods of Measurements.
2018, vol. 9, no. 3, pp. 205-214.
DOI: 10.21122/2220-9506-2018-9-3-205-214
Introduction
Diode-pumped femtosecond laser sources with pulse repetition frequencies (PRF) of hundreds of kilohertz and pulse energies of tens microjoules are of practical importance for high temporal and spectral resolution measurements, precision micromachining, optical memory and biomedicine [1]. Extremely high average output powers up to the kilowatt level could be obtained by means of direct amplification of high repetition-rate oscillators. 1.1 kW of average power at 20 MHz repetition rate with 615 fs pulses were obtained using the Innoslab Yb:YAG concept [2]. 830 W trains of 640 fs pulses at 78 MHz were demonstrated by employing large-mode area Yb-doped fiber amplifiers [3]. Pulses at lower repetition frequencies, up to a few megahertz, with substantially higher energy and peak power are preferred for many applications. These pulse trains can be generated conveniently with solid-state diode-pumped regenerative amplifiers (RAs). Up to now, the highest average power RA systems are presented by thin-disk concept RAs. For example, up to 160 W average output power at 800 kHz PRF with 750 fs pulse duration were achieved in [4]. Up to 100 W average power at 400 kHz PRF with 800 fs pulse duration were reached in [5] employing Yb:YAG thin-disk active element. Despite thin-disk based regenerative amplifier systems demonstrate high average power, it should be noted that pulse duration of such systems is not less than 700 fs. 295 fs pulses were demonstrated for thin disk RA system that applied nonlinear pulse amplification regime but with substantially reduced output power (36 W) [6]. Another approach to implementation of RA systems is based on bulk regenerative amplifiers. The highest output power reported so far for bulk RAs is 42 W at 500 kHz pulse repetition frequency obtained in RA based on the active medium with high thermooptical properties - Yb:Lu2O3 [7]. Relatively long amplified pulses of about 780 fs pulse duration obtained due to narrow gain bandwidth ofYb:Lu2O3. Substantially reduced pulse duration of 217 fs with relatively high output power of 28 W demonstrated at 500 kHz in RA based on crystal with wide gain bandwidth -Yb:CALGO [8]. But the usage of active medium with wide gain bandwidth is not a sufficient condition for obtaining short amplified pulse duration due to the strong gain narrowing effect [9] that reduce amplified pulse spectral width and increase minimal transform-limited pulse duration. Several methods for overcoming the negative contribution of gain
narrowing effect have been proposed [10, 11]. The output power of about 21 W at 200 kHz PRF with 200 fs pulse duration is obtained with Yb:KGW dual crystal system [10]. Femtosecond laser pulses with duration as short as 97 fs with output power of 1.2 W at 50 kHz PRF were obtained with the Yb:CALGO RA system which demonstrates the possibility of sub-100 fs pulses amplification [11].
Despite the availability of femtosecond lasers providing wide spectral width pulses [12-14] based on Yb seed lasers a large number of RA systems described in the literature have narrower pulse spectral width not over than 15 nm. And this also limits the amplified pulse spectral width and compressed pulse duration.
The aim ofthis work was to study the amplification of broadband chirped femtosecond pulses in regenerative amplifier based on Yb3+:CaYAlO4 crystal.
Crystal growth
Single crystals of Yb3+:CaYAlO4 (tetragonal structure, space group D174h-I4/mmm) doped with Yb3+(1.4 at. % and 3.5 at. %) were grown from stoichiometric melts by Czochralski method [15]. Yb3+ ions occupy Y3+ sites of the lattice with 9-fold coordination. Crystallization was carried out under an enclosed argon atmosphere using iridium crucibles (50 * 50 * 30 mm3) and seed crystals oriented along [110]. The pulling and rotation rates were 1.5-2.5 mm/h and 15-25 rev/min respectively. Transparent crystals 15 mm in diameter and 20-30 mm long were obtained for the present studies.
Spectroscopy
Polarized absorption spectra of Yb3+(1.4 at. %): CaYAlO4 (correspondent ytterbium volume concentration is 1.82 1020 cm-3) at room temperature were measured by a Varian CARY 5000 spect-rophotometer. The absorption cross-section spectra for different polarizations are shown in Figure 1.
Strong absorption is found for n-polarized light. A peak absorption cross-section at 979 nm was measured to be about 4 10-20 cm2, with comparatively wide bandwidth of about 9.5 nm (FWHM). For o-polarization maximal absorption cross section near 979 nm was 1.5 10-20 cm2. Radiative lifetime was estimated by using crystalline powder immersed in glycerine suspension in order to eliminate radiation trapping effect caused by significant overlap of the absorption and emission bands [16, 17]. Measured lifetime for different weight content
of Yb3+(1.4 at. %):CaYAlO4 and Yb3+(3.5 at. %): The radiative lifetime of the 2F5/2 manifold of Yb3+-
CaYAlO4 crystalline powder in glycerine suspension are shown in Figure 2. Measured kinetics of luminescence decay for Yb3+:CaYAlO4 with 1.4 at. % and 3.5 at. % concentrations are shown in Figure 3.
с 5
E 4
o° 3
CM
О 2
Г 1
с О О
'о 2,0 0) W5 1,5 сл «1,0
О 0,5
0,0
Л ---Absorption — Stimulated emission
[A / Д / l\ J \ V. - "У 4
' ' 1 ..... -1-1——Г-------1---1-1-'-1
a /' A f \
- - 4
900 920 940 960 980 1000 1020 1040 1060 1080
Wavelength, nm Figure 1 - Absorption and stimulated emission cross-section spectra of the Yb3+:CaYAlO4
460-
1л 450-
a
of
E
440-
aj
4—
—I
430-
420-
*
^ О ^ ❖ ^ ^
ions in CaYAlO4 was estimated to be (430 ± 15) ^s. The stimulated emission cross sections (Figure 1) were calculated by use of integral reciprocity method [18].
' 20 ' 40 ' 60 ' 80 ' l3o~ Weight content of powder, % Figure 2 - Measured lifetime for different weight content of Yb3+:CaYAlO4 crystalline powder in glycerine suspension
Figure 3 - Kinetics of luminescence decay 2F5/2 manifold of Yb3+-ions in CaYAlO
The Yb3+:CaYAlO4 crystal exhibits broad stimulated emission cross-section spectra in the range 990-1080 nm for both polarizations. The stimulated emission cross-section for o-pola-rization demonstrates higher value of about ~ 0.710-20 cm2 at 1030-1040 nm in comparison with ~ 0.5 10-20 cm2 for n-polarization. Obtained spectroscopic properties of the Yb3+:CaYAlO4 crystal demonstrate good agreement with described in literature data [19].
Experimental setup
The conceptual scheme of the system layout is shown in Figure 4.
Figure 4 - Experimental setup of broad-band seeded Yb3+:CaYAlO4 chirped pulse RA
As a seed source laser diode-pumped Yb:KYW oscillator was used which provided 100 fs pulse train with 70 MHz PRF and 10 nJ single pulse energy. The seed pulse spectrum was about 12.5 nm wide (FWHM) and centered at 1038 nm. A 10-m-long single mode 09/125 ^m telecom fibre was used for pulse spectral broadening and temporal stretching (ipulse ~ 7.5 ps). After passing through a Faraday isolator, the seed pulse was injected into the RA. The isolator was employed to protect the seeder from high-intensity back reflections and, at the same time, for separating the amplified output pulse from the seed oscillator. The RA setup chosen for this experiment is quite common, employing a 40-mm-long double-BaB2O4 Pockels cell for pulse injection and ejection. Pulse repetition frequency (PRF) was chosen to be 200 kHz to prevent damage of the optical elements. «Off-axes» pump layout was used for longitudinal pumping of the active element [20-22]. Main advantage of such a pump scheme is that all the cavity mirrors have highly reflecting coating at (900-1100) nm. Maximum pump power was 25 W. 2mm-long a-cut Yb3+(3.5 at. %): CaYAlO4 crystal was used as a gain medium. The last unit of the amplifier system is compressor based on transmission diffraction grating with 1000 grooves per millimetre.
Continuous wave laser experiment
At the beginning we have tested the gain crystal under CW lasing. Laser cavity had the same geometry as a RA cavity without Pockels cell. One of the HR flat mirrors was replaced by the output coupler (OC) with different transmittances. Dependencies of the laser output power on the absorbed pump power for n- and o-polarized output and different OCs are shown in Figure 5. Absorbed pump power was real time measured during the laser action.
The maximum CW output power of 7.4 W at absorbed pump power of 14.9 W with slope efficiency as high as 59.3 % was obtained with 10 % OC
transmittance and o-polarized output. The output powers of 6.6 W and 5.6 W and slope efficiencies of 50.5 % and 65.4 % were demonstrated with 5 % and 20 % OC transmittances, respectively. For n-polarization output powers of 6.3 W, 6.5 W, 4.4 W with slope efficiencies of 49.1 %, 58.2 %, 60.9 % were obtained with 5 %, 10 % and 20 % OC transmittances.
U-1^—I-1-1-1-1-1-1-i-1-1-1-[—
2 4 6 8 10 12 14 Absorbed pump power, W
8-i
Absorbed pump power, W
Figure 5 - Dependencies of output power ofYb3+:CALYO CW laser on absorbed pump power for different OC transmittances and polarizations
The tunability curves of the Yb3+(3.5 at. %): CaYAlO4 crystal were measured with 1.5 % OC transmission during CW experiments. Central wavelength of the Yb3+:CaYAlO4 laser was tuned in the range of about 100 nm from 982 to 1082 nm for n-polarisation and from 984 to 1086 nm for o-polarisation (Figure 6).
The results of CW laser experiments show high prospects of Yb3+:CaYAlO4 crystal as an active medium of laser systems operating in a wide spectral range with high average output power.
Wavelength, nm Figure 6 - Tunability curves of the CW Yb3+:CALYO laser
Before the chirped pulse RA experiment seed pulses spectral broadening in fiber was investigated. High peak power of femtosecond pulses provides efficient spectral broadening of seed pulses due to the influence of nonlinear effects such as Raman scattering and self-phase modulation. Seed pulse spectral shape after the fiber in dependence of the incident pulse energy (Emc = 0.15-7 nJ) are shown in Figure 7. Intracavity seed pulse spectrum and autocorrelation trace for maximum incident pulse energy are shown in Figure 8.
1,0-
0,8-
.ri 0,6-
м 0,4-
c
ш
0,2-
0,0-
1005 1020 1035 1050 1065 Wavelength, nm
-15 -10 -5 0 5 Time, ps
b
10 15
Seed pulses have spectral width of about 60 nm FWHM and about 7.5 ps duration while the incident pulse spectral width was about 12.5 nm. Fiber coupling efficiency was about 65 %. Seed pulse energy at the output of the fiber was about 4.5 nJ.
Chirped pulse regenerative amplification experiment
During the RA experiment we measured the output pulse train parameters (spectral width and output power) for n- and o-polarized light in the gain medium at 200 kHz PRF (Figure 9).
Figure 7 - Pulse spectra at the output of the fiber for different incident energy
Figure 8 - Intracavity pulse spectrum (a) and autocorrelation trace of RA seed pulses (b)
Figure 9 - Dependencies of spectral width and average output power on the cavity roundtrips of Yb3+:CALYO chirped pulse RA
The maximum uncompressed average output power of 5.3 W (2.9 W) was obtained for o- (n-) polarized light after 110 round trips (RT) of the pulse through the amplifier cavity, while the pulse spectral width (FWHM) decreased to 12.4 nm and 16.9 nm for o- and n-polarization states, respectively, that demonstrated strong gain narrowing effect. The amplified pulse spectrum evolution versus RT number through the amplifier for n- and o-pola-rizations are shown in Figure 10.
b
Figure 11 - Seed and amplified pulse spectra (a) and autocorrelation trace of compressed o-polarized output pulse after 55 round trips (b)
The output beam had good quality with an M2-factor of about 1.15. Measured output beam caustic and profile for Yb3+:CALYO, o-polarized broad-band seeded chirped pulse RA are shown in Figure 12.
Figure 10 - Evolution of the output pulse spectrum of Yb3+:CALYO chirped pulse RA
The data presented in the Figure 9 indicate that o-polarization is more suitable for amplification of broad-band ultrashort pulses. Wide amplified spectrum of 19.4 nm (FWHM) was demonstrated after 55 RT with output power of about 4 W (almost 80 % of maximum value) (Figure 11). Corresponding autocorrelation (AC) trace of compressed pulses with average output power of 3 W is also shown in Figure 11. Measured pulse duration was about 120 fs assuming Lorentzian pulse shape (the best fit with AC trace).
b
Figure 12 - Output beam caustic (a) and profile (b)
The profile of the beam remains Gaussian up to the highest output powers.
Mathematical modelling
To estimate the amplified pulse spectra limited mostly by gain crystal characteristics and gain narrowing effect mathematical simulation was made
a
a
with constant level of intracavity losses (~ 5 %) for wide spectral range covering active crystal gain bandwidth. Simulation was based on the split-step Fourier method [23]. Gain curve was calculated by means of the absorption (ABS) and stimulated emission (SE) cross-section spectra under a certain population of the upper laser manifold of Yb3+ ions which corresponds to our experimental conditions. Simulation results are well agreed with experimental results. Amplified pulse spectrum evolution during the amplification in the Yb3+:CALYO based chirped pulse RA is shown in Figure 13.
b
Figure 14 - Simulated and measured pulse spectra (a) and dependency of pulse spectral width on cavity roundtrip (b) for Yb3+:CALYO, n chirped pulse RA
Simulated and measured pulse spectra after 55 round trips and dependency of pulse spectral width on cavity round trips for Yb3+:CALYO, o-polarized chirped pulse RA are shown in Figure 15.
Figure 13 - Evolution of the output pulse spectrum of Yb3+:CALYO chirped pulse RA
Simulated and measured pulse spectra after 110 round trips and dependency of pulse spectral width on the number of cavity round trips for Yb3+:CALYO, n-polarized chirped pulse RA are shown in Figure 14.
b
Figure 15 - Simulated and measured pulse spectra (a) and dependency of pulse spectral width on cavity roundtrip (b) for Yb3+:CALYO, o chirped pulse RA
It is evident that simulation results are satisfactory agreed with experimental data, especially
a
a
for o-polarisation. Thus, the usage of wide-band femtosecond seed pulses for Yb3+:CALYO chirped pulse RA makes it possible to shorten the duration of amplified pulses despite the negative contribution of gain narrowing effect.
Conclusion
The results of experimental investigation of broad-band seeded Yb3+:CaYAlO4-based chirped pulse regenerative amplifier are reported for the first time to our knowledge. 120 fs-pulses (19.4 nm FWHM) with average output power of 3 W were demonstrated without any gain narrowing compensation technique. Despite the significant reduction of amplified pulse duration the task of improvement group velocity dispersion balance (including high orders of group velocity dispersion) remains relevant.
References
1. Breitling D., Föhl C., Dausinger F., Kononenko T., Konov V. Ultrashort Interaction with Materials. Femtosecond Technology for Technical and Medical Applications. F. Dausinger, F. Lichtner, H. Lubatschowski, eds. Springer, Berlin, 2004. doi: 10.1007/b96440
2. Russbueldt P., Mans T., Weitenberg J., Hoffmann H.D., Poprawe R. Compact diode-pumped 1.1 kW Yb:YAG Innoslab femtosecond amplifier. Opt. Lett., 2010, vol. 35, pp. 4169-4171. doi: 10.1364/0L.35.004169
3. Eidam Tino, Hanf Stefan, Seise Enrico, V. Andersen Thomas, Gabler Thomas, Wirth Christian, Schreiber Thomas, Limpert Jens, Tünnermann Andreas. Femtosecond fiber CPA system emitting 830 W average output power. Opt. Lett., 2010, vol. 35, pp. 94-96. https://doi.org/10.1364/0L.35.000094
4. Fleischhaker R., Gebs R., Budnicki A., Wolf M., Kleinbauer J., Sutter D.H. Compact gigawatt-class sub-picosecond Yb:YAG thin-disk regenerative chirped-pulse amplifier with high average power at up to 800 kHz. 2013 Conference on Lasers and Electro-Optics - International Quantum Electronics Conference (Optical Society of America, 2013), paper CFIE_4_1. https://doi.org/10.1109/CLE0E-IQEC.2013.6801054
5. Schneider W., Ryabov A., Lombosi Cs., Metzger T., Major Zs., Fülöp J.A., Baum P. 800-fs, 330 ^J pulses from a 100-W regenerative Yb:YAG thin-disk amplifier at 300 kHz and THz generation in LiNb03. Opt. Lett., 2014, vol. 39, pp. 6604-6607. https://doi.org/10.1364/0L.39.006604.
6. Pouysegur J., Delaigue M., Honninger C., Zaouter Y., Georges P., Druon F., Mottay E. Numerical
and Experimental Analysis of Nonlinear Regenerative Amplifiers Overcoming the Gain Bandwidth Limitation. Selected Topics in Quantum Electronics, IEEE Journal of, 2015, vol. 21, no. 1, pp. 212, 219. https://doi.org/10.1109/JSTQE.2014.2321520
7. Caracciolo E., Pirzio F., Kemnitzer M., Gorjan M., Guandalini A., Kienle F., Agnesi A., Aus Der Au J. 42 W femtosecond Yb:Lu2O3 regenerative amplifier. Opt. Lett., 2016, vol. 41, pp. 3395-3398. https://doi.org/10.1364/0L.41.003395
8. Caracciolo E., Kemnitzer M., Guandalini A., Pirzio F., Aus der Au J., Agnesi A. 28-W, 217 fs solid-state Yb:CAlGd04 regenerative amplifiers. Opt. Lett., 2013, vol. 38, pp. 4131-4133. https://doi.org/10.1364/0L.38.004131.
9. Raybaut P., Balembois F., Druon F., Georges P. Numerical and experimental study of gain narrowing in ytterbium-based regenerative amplifiers. IEEE Journal of Quantum Electronics, 2005, vol. 41, no. 3, pp. 415425. doi: 10.1109/JQE.2004.841930
10. Kim G.H., Yang J., Chizhov S.A., Sall E.G., Kulik A.V., Yashin V.E., Kang U. A high brightness Q-switched oscillator and regenerative amplifier based on a dual-crystal Yb:KGW laser. Laser Phys. Lett., 2013, vol. 10, 125004 (5 p.). https://doi.org/10.1088/1612-2011/10/12/125004
11. Pouysegur Julien, Delaigue Martin, Zaouter Yoann, Hönninger Clemens, Mottay Eric, Jaffrès Anaël, Loiseau Pascal, Viana Bruno, Georges Patrick, Druon Frédéric. Sub-100-fs Yb:CALG0 nonlinear regenerative amplifier. Opt. Lett., 2013, vol. 38, pp. 5180-5183. https://doi.org/10.1364/0L.38.005180
12. Pirzio Federico, Cafiso D. Di Dio Samuele, Kemnitzer Matthias, Guandalini Annalisa, Kienle Florian, Veronesi Stefano, Tonelli Mauro, Aus der Au Juerg, Agnesi Antonio. Sub-50-fs widely tunable Yb:CaYAl04 laser pumped by 400-mW single-mode fiber-coupled laser diode. Opt. Express, 2015, vol. 23, pp. 9790-9795. https://doi.org/10.1364/0E.23.009790
13. Gao Ziye, Zhu Jiangfeng, Wang Junli, Wei Zhiyi, Xu Xiaodong, Zheng Lihe, Su Liangbi, Xu Jun. Generation of 33 fs pulses directly from a Kerr-lens mode-locked Yb:CaYAl04 laser. Photon. Res., 2015, vol. 3, pp. 335338. https://doi.org/10.1364/PRJ3.000335
14. Ma Jie, Huang Haitao, Ning Kaijie, Xu Xiaodong, Xie Guoqiang, Qian Liejia, Ping Loh Kian, Tang Dingyuan. Generation of 30 fs pulses from a diode-pumped graphene mode-locked Yb:CaYAl04 laser. Opt. Lett., 2016, vol. 41, pp. 890-893. https://doi.org/10.1364/0L.41.000890
15. Kaminskii A.A., PetrosyanA.G., 0vanesyan K.L., Shirinyan G.0., Butaeva T.I., Markosyan A.A. Two generation channels of the CaYAl04 disordered crystal. Inorganic Materials, 1991, vol. 27, pp. 426-427.
16. Sumida D.S., Fan T.Y. Effect of radiation trapping on fluorescence lifetime and emission cross section measurements in solid-state laser media. Opt. Lett., 1994, vol. 19, pp. 1343-1345. https://doi.org/10.1364/OL.19.001343
17. Kühn Henning, Fredrich-Thornton Susanne T., Kränkel Christian, Peters Rigo, Petermann Klaus. Model for the calculation of radiation trapping and description of the pinhole method. Opt. Lett., 2007, vol. 32, pp. 19081910. https://doi.org/10.1364/0L.32.001908
18. Yasyukevich A.S., Shcherbitskii V.G., Kisel V.E., Mandrik A.V., Kuleshov N.V. Integral method of reciprocity in the spectroscopy of laser crystals with impurity centers. Journal ofApplied Spectroscopy, 2004, vol. 71, no. 2, pp. 202208. https://doi.org/10.1023/BJAPS.0000032875.04400.a0.
19. Li Dongzhen, Xu Xiaodong, Zhu Haomiao, Chen Xueyuan, Tan Wei De, Zhang Jian, Tang Dingyuan, Ma Jan, Wu Feng, Xia Changtai, Xu Jun. Characterization of laser crystal Yb:CaYAl04. J. Opt. Soc. Am. B 28, 2011, pp. 1650-1654. https://doi.org/10.1364/J0SAB.28.001650
20. Kisel V.E., Rudenkov A.S., Pavlyuk A.A., Kovalyov A.A., Preobrazhenskii V.V., Putyato M.A., Rubtsova N.N., Semyagin B.R., Kuleshov N.V. Highpower, efficient, semiconductor saturable absorber mode-locked Yb:KGW bulk laser. Opt. Lett, 2015, vol. 40, pp. 2707-2710. https://doi.org/10.1364/OL.40.002707
21. Rudenkov Alexander, Kisel Viktor, Matrosov Vladimir, Kuleshov Nikolai. 200 kHz 5.5 W Yb3+:YVO4-based chirped-pulse regenerative amplifier. Opt. Lett., 2015, vol. 40, pp. 3352-3355. https://doi.org/10.1364/OL.40.003352.
22. Rudenkov Alexander, Kisel Viktor, Yasuke-vich Anatol, Hovhannesyan Karine, Petrosyan Ashot, Kuleshov Nikolay. Yb3+:LuAlO3 crystal as a gain medium for efficient broadband chirped pulse regenerative amplification. Opt. Lett., 2017, vol. 42, pp. 2415-2418. https://doi.org/10.1364/OL.42.002415
23. Agrawal G.P. Nonlinear Fiber Optics (Fourth Edition). Optics and Photonics, Academic Press, San Diego, 2006, p. 529. https://doi.org/10.1016/B978-0-12-369516-1.X5000-6.
