CC BY
83
UDC 669/713-048/25
Doi: 10.31772/2587-6066-2019-20-1-88-98
For citation: Ivanov Yu. F., Eresko S. P., Ahmadeev Yu. H., Lopatin I. V., Klopotov А. А. [Development of combined electron-ion-plasma method for formation of multiphase submicro-nanoscale alloys based on aluminum].
Siberian Journal of Science and Technology. 2019, Vol. 20, No. 1, P. 88-98. Doi: 10.31772/2587-6066-2019-201-88-98
Для цитирования: Иванов Ю. Ф., Ереско С. П., Ахмадеев Ю. Х., Лопатин И. В., Клопотов А. А. Разработка комбинированного электронно-ионно-плазменного метода формирования многофазных субмикро-нано-размерных сплавов на основе алюминия // Сибирский журнал науки и технологий. 2019. Т. 20, № 1. С. 88-98. Doi: 10.31772/2587-6066-2019-20-1-88-98
DEVELOPMENT OF COMBINED ELECTRON-ION-PLASMA METHOD FOR FORMATION OF MULTIPHASE SUBMICRO-NANOSCALE ALLOYS BASED ON ALUMINUM
Yu. F. Ivanov1, S. P. Eresko2, Yu. H. Ahmadeev1, I. V. Lopatin1, А. А. Klopotov3,4*
institute of High Current Electronics of the SB RAS 2/3, Akademicheskiy Av., Tomsk, 634055, Russian Federation
2Reshetnev Siberian State University of Science and Technology 31, Krasnoyarsky Rabochy Av., Krasnoyarsk, 660037, Russian Federation
3Tomsk State University of Architecture and Building 2, Solyanaya Sq., 6340032, Tomsk, Russian Federation
4National Research Tomsk State University 36, Lenin Av., Tomsk, 634050, Russian Federation *Е-mail: [email protected]
Aluminum-based alloys are widely used in many branches of modern industry (aviation, mechanical engineering, shipbuilding, instrument-making, energy and medicine, etc.). The promising method for further expanding the scope of these alloys is surface treatment based on the use of concentrated energy fluxes (laser beams, plasma flows, powerful ion beams, continuous and pulsed electron beams). The purpose of this paper is to establish the possibilities of integrated electron-ion-plasma modification of the structure and properties of the surface layer of technically pure aluminum A7. The surface alloy was formed in a single vacuum cycle using the "KOMPLEX" facility (ISE SB RAS) by spraying a titanium film with a thickness of 0.5 pm and the subsequent irradiation with an intense pulsed electron beam in the aluminum melting mode. After 20 "spraying/irradiation" cycles, nitriding (540 °C, 8 h) of the formed surface alloy was performed in a low-pressure gas discharge plasma using the plasma generator "PINK". Surface alloy studies were carried out applying the modern materials science methods (scanning and transmission electron diffraction microscopy, X-ray phase analysis, determination of hardness and wear resistance). The choice of elements alloying the surface layer of aluminum was based on the analysis of binary state diagrams of Al-N, Al-Ti, Ti-N systems and the isotermal section of the ternary system Al-Ti-N. It has been shown that formation of an entire series of binary and ternary compounds, including MAX-phases of the composition Ti2AlN and Ti4AlN3, is observed under equilibrium conditions in the Al-Ti-N system. The carried out research has allowed to state that an integrated method of electron-ion-plasma modification of technically pure A7 aluminum by nitriding (540 °C, 8 h) of the surface alloy formed by pulsed melting in vacuum of the Al-Ti system (20 "spraying/irradiation" cycles with an electron beam with parameters 10 J/cm2; 50 ps; 10pulses; the titanium film thickness in each cycle 0.5 pm) leads to formation of a multiphase multielement submicro-nanocrystalline surface layer up to 20 pm thick. It is shown that the mechanical (microhardness) and tribological (wear resistance and friction coefficient) properties of the formed surface layer exceed manifold the properties of the original commercially pure aluminum A7.
Keywords: aluminum, electron-ion-plasma processing, nitriding, structural researches, nanostructure, properties.
РАЗРАБОТКА КОМБИНИРОВАННОГО ЭЛЕКТРОННО-ИОННО-ПЛАЗМЕННОГО МЕТОДА ФОРМИРОВАНИЯ МНОГОФАЗНЫХ СУБМИКРОНАНОРАЗМЕРНЫХ СПЛАВОВ
НА ОСНОВЕ АЛЮМИНИЯ
Ю. Ф. Иванов1, С. П. Ереско2, Ю. Х. Ахмадеев1, И. В. Лопатин1, А. А. Клопотов3,4*
Институт сильноточной электроники СО РАН Российская Федерация, 634055, г. Томск, просп. Академический, 2/3 2Сибирский государственный университет науки и технологий имени академика М. Ф. Решетнева Российская Федерация, 660037, г. Красноярск, просп. им. газеты «Красноярский рабочий», 31 3Томский государственный архитектурно-строительный университет Российская Федерация, 634003, г. Томск, пл. Соляная, 2 4Национальный исследовательский Томский государственный университет Российская Федерация, 634055, Томск, ул. Ленина 36 *Е-таЛ: [email protected]
Сплавы на основе алюминия широко используются во многих отраслях современной промышленности (авиации, машиностроении, кораблестроении и приборостроении, энергетике, медицине и т. д.). Перспективными методами дальнейшего расширения сферы применения данных сплавов является поверхностная обработка, основанная на использовании концентрированных потоков энергии (лучи лазера, потоки плазмы, мощные ионные пучки, непрерывные и импульсные электронные пучки). Целью настоящей работы является установление возможностей комплексного электронно-ионно-плазменного модифицирования структуры и свойств поверхностного слоя технически чистого алюминия марки А 7. Формирование поверхностного сплава осуществляли в едином вакуумном цикле на установке «КОМПЛЕКС» (ИСЭ СО РАН) путем напыления пленки титана толщиной 0,5 мкм и последующего облучения интенсивным импульсным электронным пучком в режиме плавления алюминия. После 20 циклов «напыления/облучения» проводили азотирование (540 °С, 8 ч) сформированного поверхностного сплава в плазме газового разряда низкого давления с использованием плазмогенератора «ПИНК». Исследования поверхностного сплава осуществляли методами современного материаловедения (сканирующая и просвечивающая электронная дифракционная микроскопия, рентгенофазовый анализ, определение твердости и износостойкости). Выбор легирующих поверхностный слой алюминия элементов был основан на анализе бинарных диаграмм состояний систем А1-Ы, А1-Т1, Т1-Ы и изотерического сечения тройной системы А1-Т1-Ы. Показано, что в равновесных условиях в системе А1-Т1-Ы наблюдается формирование целого ряды двойных и тройных соединений, в том числе и МАХ-фаз состава Т12А1Ы и Т14А1Ы3. В результате выполненных исследований установлено, что комплексный метод электронно-ионно-плазменного модифицирования технически чистого алюминия марки А7 путем азотирования (540 °С, 8 ч) поверхностного сплава, сформированного импульсным плавлением в вакууме системы А1-Т1 (20 циклов «напыления/облучения» электронным пучком с параметрами 10 Дж/см2; 50 мкс; 10 имп.; толщина пленки титана в каждом цикле 0,5 мкм), приводит к формированию многофазного многоэлементного субмикронанокристаллического поверхностного слоя толщиной до 20 мкм. Показано, что механические (микротвердость) и трибологические (износостойкость и коэффициент трения) свойства сформированного поверхностного слоя многократно превосходят свойства исходного технически чистого алюминия А 7.
Ключевые слова: алюминий, азотирование, структурные исследования, электронно-ионно-плазменная обработка, наноструктура, свойства.
Introduction. Titanium and aluminum-based alloys are widely used in the aerospace industry, mechanical engineering and shipbuilding, medicine, etc. [1; 2]. In many cases extension of scope of these materials is based on the improvement of properties of a surface layer of a detail or product. It happens due to formation of wear resistant, hard and super hard coatings; creation of multielement multiphase sub-micro nanocrystal surface layers; and integrated processing combining formation of multipurpose coatings on preliminary modified surface of a detail [1-5]. Perspective methods of surface treatment are those based on the use of concentrated energy streams (laser beams, plasma streams, powerful ion beams, continuous and pulse electron beams) [5-12]. Employing this approach allows to drastically improve material properties connected with modifying surface layer condition
(hardness, wear resistance, resistance to the influence of hostile environment, etc.) [5-13]. One of the perspective methods of metals and alloys surface treatment is the approach based on the integrated impact of plasma streams and intensive pulse electron beams on the material surface [5; 13].
The purpose of the present research is to find opportunities for integrated electronic ion-plasma modification of the structure and properties of commercially pure aluminum surface layer.
Material and method of research. Material of research - commercially pure aluminum А7 brand (0.15Si, 0.16Fe, 0.01Cu, 0.03Mn, 0.02Mg, 0.04Zn, 0.03Ga, 0.01Ti, balance Al, weight. %) [14]. Specimen dimensions 15x15x5 mm. The surface alloy was formed in a single vacuum cycle using the "KOMPLEX" facility
(ISE SB RAS) by spraying a titanium film with a thickness of 0.5 ^m and the subsequent irradiation with an intense pulsed electron beam in the aluminum melting mode. After 20 "spraying/irradiation" cycles, nitriding (540 °C, 8 h) of the formed surface alloy was performed in a low-pressure gas discharge plasma using the plasma generator "PINK". Research into the element and phase structure, defective substructure condition was carried out applying the methods of scanning electron microscopy (Philips SEM-515 with microanalyzer EDAX ECON IV) and transmission diffraction electron microscopy (JEOL JEM-2100 F), X-ray diffraction analysis (X-ray diffrac-tometer Shimadzu XRD 6000). Material properties were characterized by hardness (PMT 3, indentation load 0.2 H). Tribological studies (wear resistance and friction coefficient identification) were carried out on tribometer Pin on Disc and Oscillating TRIBOtester (TRIBOtechnic, France) under the following parameters: steal ball of 6 mm diameter, track radius - 2 mm, indentation load and track length vary depending on the ware resistance factor of the material under study.
Results and discussions. Fig. 1 shows binary state diagrams Al-N, Al-Ti, Ti-N and Isothermal section of the ternary system Al-Ti-N. Two of the three alloying elements of the ternary system Al-Ti-N are metals, while the third one nitrogen is a non-metal and belongs to VB group of the Periodic table. Nitrogen atoms possess five electrons on the outer 5- and /»-shells ([He]2s22p3). With such electronic structure nitrogen quite easily attaches three more electrons which is a characteristic of non-metal.
System Al-N. Nitrogen is almost insoluble in Al neither in liquid, nor in hard states [15]. In the Al-N system existence of only one connection in the field of the stoichiometric structure of AlN with hexagonal structure was found (Pearson's symbol hP4, pr. gr. R63ts, ZnS prototype) (fig. 1).
System Ti-N. Titan possess a characteristic of activel interaction with nitrogen. It finds reflection in formation of compounds in the Ti-N system in the form of solid solutions with variable structures and with wide areas of homogeneity: P-(Ti,N), a-(Ti,N), 8-TiNX (cF8, NaCl) (fig. 1) [16]. In compounds 8-TiNX atoms Ti form a metal face-centered cubic sublattice, where in octahedral interstices interstitial (nitrogen) or vacancies may be present. In not stoichiometric disordered compound 8-TiNX change of structural vacancies concentration causes wide area of homogeneity. Under the temperature of ~ 1100 °C and content of N atoms ~33% from the phase 8-TiNX nitride e-Ti2N (tP6, anti-TiO2) with the narrow area of homogeneity is formed. Besides, in a number of studies existence of three intermediate phases was identified: Z-Ti4N3-X (hR8) [17], n-Ti3N2-X (hR6, VTa2C2) [18; 19], Ti4N3-x (hR2, V4C3) [17; 18].
System Al-Ti-N. Inside isothermal triangle in the system Al-Ti-N existence of three nitride compounds of strong stoichiometric ratio was found (fig. 1): Xj-Ti3AlN (Pearson's symbol cP5, prototype CaTiO3) [22; 23]; T2-Ti2AlN (hP8, Cr2AlC) [24]; x3-Ti4AlN3 (hP16, Ti4AlN3) [25]. Apart from that, in [26-28] metastable condition Ti1-xAlxN (cF8, NaCl).
Out of the three compounds formed in the system Al-Ti-N, compound xi-Ti3AlN proves the most stable [29] and belongs to the phase group H [30]. Literature shows that there are several ways of how compounds xi-Ti2AlN can be prepared. Let us demonstrate the synthesis of particles with Ti2AlN phase. First, under exothermic reaction of powders Al and Ti in nitrogen atmosphere [31]. Second, as a result of powders Al and TIN hot pressing and subsequent homogenization of samples under the temperature 850 °C within 200 hours [32]. Third, when sintering under above 1500 °C from powders AlN and Ti [33; 34]. Fourth, as a result of 24 hours roasting under between 1275 °C and 1600 °C and 1100 MPa of powder bland Al, Ti, TiN and AlN nitrides pressed under room temperature [35]. Fifth, when nitriding Al-Ti alloys as a result of roasting under 1000 °C [36]. Sixth, when heating a powder bland consisting of two parts Ti and one part of AlN under 1400 °C for 48 hours under the pressure of ~ 40 MPa [24]. Seventh, powder bland AlN and Ti vacuum sintering under 10-3 Pa for 16 hours [37].
Recently great attention is drawn to perspective materials - polycrystalline nanolaminates. This class of materials represents machine processed ceramics which is stable at high temperatures [38-41]. In terms of structure nanolaminates, which are called still MAX phases, [42] represent threefold compounds with structure Mn+iAXn (M = transition metal, A = element of IIIA or IVA group of the Periodical table, X = C or N, n accepts integer values 1, 2, 3). MAX are phases representing laminated hexagonal structure with space group P63/mmc with two formula units in a space unit (fig. 2). The unique distinctive feature of these materials is a laminated crystal lattice, a natural arrangement of layers of atoms M- and Aelements.
According to literature [42], more than 70 of the popular nanolaminates are titanium nitride-based. They are phases Ti2AlN (211) and Ti4AlN3 (413), where element X is nitrogen.
In the light of the aforesaid it is possible to assume that application of the high-energy electronic ion-plasma integrated processing of aluminum surface in a uniform vacuum cycle combining formation of "film (tita-nium)/(aluminum) substrate" system, radiation with an intensive pulse electron beam of aluminum surface in the melting mode, and subsequent saturation of the alloyed layer with nitrogen atoms of low pressure gas category plasma can lead to specific structural and phase states which will cause formation of a multiphase surface with the increased physical and mechanical properties. The research of commercially pure aluminum modified layer phase structure was conducted applying the methods of X-ray diffraction analysis. It is revealed that the surface layer is multiphase material and contains a-Ti (5.2 mass. %), Al3Ti (58.4 mass. %), AlN (24.2 mass. %) and Al (12.2 mass. %).
The undertaken research showed that the surface layer up to 20 microns thick has sub-microcrystalline, typical structure of which is provided in fig. 3.
_I_I_I_I_I_I_I_I_I_
Ti 20 40 60 80 Al at.% Al
Fig. 1. Isothermal section at 900 °C of the Al-Ti-N ternary system [20; 21] and binary state diagrams of the Al-N [15], Al-Ti [15] and Ti-N systems [16]
Рис. 1. Изотермическое сечение при 900 °С тройной системы Al-Ti-N [20; 21] и бинарные диаграммы состояний систем Al-N [15], Al-Ti [15] и Ti-N [16]
211 312 413
Fig. 2. Crystal structure of MAX-phases with transition metals (M) with layers of elements A (C or N) from groups IIIA and IVA [41]
Рис. 2. Кристаллическая структура MAX-фаз с переходными металлами (M) со слоями из элементов A (C или N) из групп IIIA и IVA [41]
Fig. 3. Electron-microscopic image of the surface layer of commercially pure aluminum grade A7 modified by nitriding (540 °C, 8 h) of a surface alloy formed by pulsed melting in a vacuum of the Al-Ti system (20 sputtering/irradiation cycles) with an electron beam with parameters J/cm2; 50 ^s; 10 imp.; titanium
film thickness in each cycle 0.5 ^m): a - arrows indicate bend contours of extinctions; b - dislocational substructure of material
Рис. 3. Электронно-микроскопическое изображение поверхностного слоя технически чистого алюминия марки А7, модифицированного путем азотирования (540 °C, 8 ч) поверхностного сплава,
сформированного импульсным плавлением в вакууме системы Al-Ti (20 циклов «напыления/облучения» электронным пучком с параметрами 10 Дж/см2; 50 мкс; 10 имп.; толщина пленки
титана в каждом цикле 0,5 мкм): а - стрелками указаны изгибные контуры экстинкции; b - дислокационная субструктура материала
Crystallite sizes change ranging from 0.2 microns up to 0.9 microns.
Crystallites have various forms changing from globular to facetted. In crystallites volumes a dislocation substructure in the form of chaotically distributed dislocations is observed (fig. 3, b). The scalar density of dislocations changes in limits (0.8 -r- 1.1)x1010 cm-2
Electronic and microscopic image of crystallites is characterized by a large number of flexural extiction contours (fig. 3, contours are specified by arrows). Existence on electronic and microscopic images of such contours indicates curvature torsion of a crystal lattice of the studied foil that testifies, in turn, elastic tension of the studied material layer [43]. Generally, contours start from crystallite border lines. This fact proves that the crystallite border lines are the source of material elastic tension [44]. A number of studies [45-47] shows that the cross sizes of a flexural extinction contour are inversely proportional to tension amplitude of this particular foil section. Analyzing the electronic and microscopic image of the material structure shown in fig. 3, it can be noted that the cross sizes of flexural contours are minimum at crystallites border lines and are maximum in the center of the crystallite. Therefore, amplitude of curvature torsion of a crystal lattice of material is minimal in the center of crystallites while increases as approaching the border line of the section.
Applying the methods of the micro-diffraction analysis with the subsequent indicating of micro-diffraction
patterns it was found that crystallites are formed by the phases a-Ti, Al3Ti and Al that was also revealed by the methods of the X-ray phase analysis. In most cases grains of a-titanium and aluminum are located in chains parallel to the modifiable surface of a sample.
On borders of crystallites extended layers having nanocrystal structure with particles size of 10-20 nanometers are observed. A typical image of such structure is show in fig. 4. The microdiffraction patterns analysis received from similar foil sections shows that nanocrys-tals are aluminum nitrides. As a rule, such layers are formed along the titan aluminide Al3Ti grain sections borders. Nanodimensional allocations of aluminum nitride particles are found in aluminum grains volume as well.
Electronic microscope JEOL JEM-2100 F allows studies applying the methods of electron microprobe analysis, distribution of chemical elements forming the material. Results of such research of the modified layer of commercially pure aluminum are given in fig. 5. Nitrogen atoms distribution in the structure of the studied material attracts a lot of attention. It is clear that in the aluminum layer (substrate), adjacent to the modified layer (the lower part of the picture in fig. 5) atoms of nitrogen are distributed unevenly, concentrating along borders of a cellular dislocation substructure. In aluminum grains volume located in the modified layer (specified by an arrow fig. 5), atoms of nitrogen form nanodimensional objects which are obviously aluminum nitride particles.
Properties of thealuminnum modified layer was characterized by the size of microhardness and wear resistance.
As a result of the research it was revealed that modifying of commercially pure aluminum of A7 brand by nitriding (540 °C, 8 h) of the surface alloy formed by pulse melting in the system vacuum.
Al-Ti (20 cycles "dusting/radiation" via the electron beam with the parameters of 10 J/cm2; 50 microsec; 10 imp.; thickness of titan film in each cycle equals 0.5 microns) leads to formation of a surface layer which micro-firmness by 9 times exceeds the hardness of the initial material, wear resistance is 400 times higher, friction coefficient is 3.5 times less than that of the initial material.
Fig. 4. Electron-microscopic image of the surface layer of technically pure aluminum grade A7, modified by nitriding (540 °C, 8 h) of a surface alloy formed by pulsed melting in a vacuum of the Al-Ti system (20 sputtering / irradiation cycles) with an electron beam with parameters 10 J / cm2; 50 ^s; 10 imp; film thickness of titanium in each cycle (0.5 ^m): a, b - bright-field images; c - dark field obtained in the [200] AlN reflex; d - microelectron diffraction pattern. The arrows on fig. 4, a, b indicate aluminum nitride particles located along the boundaries of titanium aluminide; on fig. 4, g is the reflex in which the dark-field image was obtained
Рис. 4. Электронно-микроскопическое изображение поверхностного слоя технически чистого алюминия марки А7, модифицированного путем азотирования (540 °C, 8 ч) поверхностного сплава, сформированного импульсным плавлением в вакууме системы Al-Ti (20 циклов «напыления/облучения» электронным пучком с параметрами 10 Дж/см2; 50 мкс; 10 имп.; толщина пленки титана в каждом цикле 0,5 мкм): а, b - светлопольные изображения; c - темное поле, полученное в рефлексе [200] AlN; d - микроэлектронограмма. Стрелками на рис. 4, а, b указаны частицы нитрида алюминия, расположенные вдоль границ алюминида титана; на рис. 4, d - рефлекс, в котором было получено темнопольное изображение
Л
Fig. 5. Electron-microscopic image of the surface layer of technically pure aluminum grade A7 modified by nitriding (540 °C, 8 h) of a surface alloy formed by pulsed melting in a vacuum of the Al-Ti system (20 sputtering / irradiation cycles) with an electron beam with parameters 10 J / cm 2 ; 50 ^ s; 10 imp.; film thickness of titanium in each cycle 0.5 ^ m) (a); image of the foil part (a) obtained in the characteristic X-ray radiation of titanium atoms (TiKa) (b) and nitrogen (NKa) (c); d - combined image of the foil part (a) obtained in the characteristic X-ray radiation of titanium atoms (TiKa) and nitrogen (NKa); arrows indicate aluminum grains
Рис. 5. Электронно-микроскопическое изображение поверхностного слоя технически чистого алюминия марки А7, модифицированного путем азотирования (540 °С, 8 ч) поверхностного сплава, сформированного импульсным плавлением в вакууме системы Л1-Т1 (20 циклов «напыления/облучения» электронным пучком с параметрами 10 Дж/см2; 50 мкс; 10 имп.; толщина пленки титана в каждом цикле 0,5 мкм) (а); изображение участка фольги (а), полученное в характеристическом рентгеновском излучении атомов титана (Т1Ка) (Ь) и азота (ЫКа) d - совмещенное изображение участка фольги (а), полученное в характеристическом рентгеновском излучении атомов титана (Т1Ка) и азота (МКа). Стрелками указаны зерна алюминия
Conclusion. The analysis of binary charts of Al-N, Al-Ti and TIN systems conditions and isothermal section of the threefold AL-TIN system is made. It is shown that under equilibrium conditions in these systems formation of double and threefold compound including the MAX phases of Ti2AlN h Ti4AlN3 structure is observed.
It is established that a complex method of electronic ion-plasma modifying of commercially pure aluminum of A7 brand by nitriding (540 0C, 8 hours) of the surface alloy formed by pulse melting in an Al-Ti system vacuum
(20 cycles "dusting/radiation" an electron beam with the parameters of 10 J/cm2; 50 microsec; 10 imp.; thickness of a titan film in each cycle equals 0.5 microns) leads to formation of a multiphase multi-element sub-micro nanocrystal surface layer up to 20 microns thick.
Mechanical (micro-hardness) and tribological (wear resistance and friction coefficient) properties of the formed surface layer drastically surpass the properties of initial commercially pure A7 aluminum.
Acknwledgements. The authors are grateful to E. A. Petrikova and O. S. Tolkachev for their active participation in the research of the modified material. The work was partially supported by RFBR grant (project № 19-08-00248).
Благодарности. Авторы выражают благодарность Е. А. Петриковой и О. С. Толкачеву за активное участие в проведении исследований модифицированного материала. Работа выполнена при частичной финансовой поддержке гранта РФФИ (проект № 19-08-00248).
References
1. Belov A. F., Benediktova G. P., Viskov A. S. Stroyeniye i svoystva aviatsionnykh materialov [Structure and properties of aviation materials]. Moscow, Metallur-giya Publ., 1989, 368 p.
2. Rakhmankulov M. M. Metallurgiya strate-gicheskikh metallov i splavov [Metallurgy of strategic metals and alloys]. Moscow, Teplotekhnik Publ., 2008, 504 p.
3. Kalachev B. A., Elagin V. I., Livanov V. A. Met-allovedeniye i termicheskaya obrabotka tsvetnykh met-allov i splavov [Metallurgy and heat treatment of non-ferrous metals and alloys]. Moscow, MISiS Publ., 2005, 432 p.
4. Beletskiy V. M., Krivov G. A. Alyuminiyevyye splavy. Sostav. Svoystva, tekhnologiya, primeneniye [Aluminum alloy. Composition, properties, technology, application]. Kiyev, KOMINTEKh Publ., 2005, 365 p.
5. Koval N. N., Ivanov Yu. F. Elektronno-ionno-plazmennaya modifikatsiya poverkhnosti tsvetnykh met-allov i splavov [Electron-ion-plasma modification of the surface of non-ferrous metals and alloys].Tomsk, NTL Publ., 2016, 312 р.
6. Kovaly N. N., Ivanov Yu. F. Evolyutsiya struktury poverkhnostnogo sloya stali. podvergnutoy elektronno-ionno-plazmennym metodam obrabotki [Evolution of the structure of the surface layer of steel subjected to electron-ion-plasma treatment]. Tomsk, NTL Publ., 2016, 304 p.
7. Gribkov F. I. Grigoryev. B. A. Kalin V. A. Per-spektivnyye radiatsionno-puchkovyye tekhnologii obrabotki materialov [Advanced radiation-beam technologies of materials processing]. Moscow, Kruglyy stol Publ., 2001, 528 p.
8. Kadyrzhanov K. K., Komarov F. F., Pogrebnyak A. D. lonno-luchevaya i ionno-plazmennaya modifi-katsiya materialov [Ion-beam and ion-plasma modification of materials]. Moscow, MGU Publ., 2005, 640 p.
9. Pout Dzh. M., Foti G., Dzhekobson D. K. Modifikatsiya i legirovaniye poverkhnosti lazernymi. ionnymi i elektronnymi puchkami [Modification and alloying of the surface with laser, ion and electron beams]. Moscow, Mashinostroyeniye Publ., 1987, 424 p.
10. Gromov V. E., Ivanov Yu. F. Struktura, fazovyy sostav i svoystva titana posle kompleksnykh uprochnya-yushchikh tekhnologiy [Structure, phase composition and properties of titanium after complex hardening technologies]. Novokuznetsk, SibGIU Publ., 2015, 304 p.
11. Shulov V. A., Paykin A. G., Novikov A. S. Sil-notochnyye elektronnyye impulsnyye puchki dlya aviat-sionnogo dvigatelestroyeniya [Pulsed high-current electron beams for aircraft engines]. Moscow, Artek Publ., 2012.
12. Uglov V. V., Cherenda N. N., Anishchik V. M., Astashinskiy V. M., Kvasov N. T. Modifikatsiya materialov kompressionnymi plazmennymi potokami [Modification of structure and properties of eutectic silumin by electron-ion-plasma treatment]. Minsk, BGU Publ., 2013, 248 p.
13. Laskovnev A. P., Ivanov Yu. F., Petrikova E. A. Modifikatsiya struktury i svoystv evtekticheskogo silumina elektronno-ionno-plazmennoy obrabotkoy [Modification of structure and properties of eutectic silumin by electron-ion-plasma treatment]. Minsk, Belaruskaya Navuka Publ., 2013, 287 p.
14. GOST 11069-2001. Alyuminiy pervichnyy. Marki. Mezhgosudarstvennyy sovet po standartizatsii. metrologii i sertifikatsii [State Standard Primary aluminum. Brands. Interstate Council for standardization, Metrology and certification]. Minsk, 2001.
15. Lyakishev N. P. Diagrammy sostoyaniya dvoynykh metallicheskikh system [State diagrams of double metal systems]. Moscow, Mashinostroyeniye Pabl., 1996, Vol. 1, 992 p.
16. Lyakishev N. P. Diagrammy sostoyaniya dvoynykh metallicheskikh system [State diagrams of double metal systems]. Moscow, Mashinostroyeniye Pabl., 2001, Vol. 3, 872 p.
17. Lengauer W., Ettmayer P. The Crystal Structure of a New Phase in the Titanium-Nitrogen System. J. Less-Common Met. 1986. Vol. 120, P. 153-159.
18. Rogl P., Schuster J.C. Ti-B-N (Titanium - Boron -Nitrogen) in Phase Diagrams of Ternary Boron Nitride and Silicon Nitride Systems. Materials Park, Ohio: Materials Informations Soc. 1992. P. 103-106.
19. Lengauer W. The Crystal Structure of n-Ti3N2_x: An Additional New Phase in the Ti-N System. J. Less-Common Met. 1986, Vol. 125, P.127-134.
20. Durlu N., Gruber U., Pietzka M. A. Phases and Phase Equilibria in the Quaternary System Ti-Cu-Al-N at 850 °C. Z. Metallkd. 1997, Vol. 97, P. 390-400.
21. Procopio A. T., El-Raghy T., Barsoum M. W. Synthesis of Ti4AlN3 and Phase Equilibria in the Ti-Al-N System. Metall. Mater. Trans. 2000, Vol. 31 A, P. 373-378.
22. Schuster J. C., Bauer J. The Ternary System Titanium-Aluminium-Nitrogen. J. Solid State Chem. 1984, Vol. 53, P. 260-265.
23. Schuster J. C., Bauer J., Nowotny H. Applications to Materials Science of Phase Diagrams and Crystal Structures in the Ternary Systems Transition Metal-Aluminium-Nitrogen. Rev. Chim. Miner. 1985, Vol. 22, P. 546-554.
24. Barsoum M. W., Ali M., El-Raghy T. Processing and Characterization of Ti2AlC, Ti2AlN and Ti2AlC0.5N0.5. Metall. Trans. 2000, Vol. A 31A, P. 1857-1865.
25. Barsoum M. W. Rawn C. J., El-Raghy T., Procopio A. T., Porter W. D., Wang H., Hubbard C. R. Thermal Properties of Ti4AlN3. J. Appl. Phys. 2000, Vol. 87, P. 8407-8414.
26. Petrov I., Mojab E., Adibi F., Greene J. E., Hultman L., Sundgren J.-E. Interfacial Reactions in Epitaxial Al/Ti1-xAlxN (0 < x < 0.2) Model Diffusion-Barrier Structure. J. Vac. Sci. Technol. 1993, Vol. A11, P. 11-17.
27. Tanaka Y., Guer T. M., Kelly M., Hagstrom S. B., Ikeda T. Strusture and Properties of (Tii-xAlx)N Films Prepared by Reactive Sputtering. Thin Solid Films. 1993, Vol. 228, P. 238-241.
28. Ikeda T., Satoh H. Phase Formation and Characterization of Hard Coatings in the Ti-Al-N System Prepared by the Cathodic Arc Ion Platting Method. Thin Solid Films. 1991, Vol. 195, P. 99-110.
29. Wu Z. L., Pope D. P., Vitek V. Ti2NAl in L12 Al3Ti-Base Alloys. Metall. Mater. Trans. 1995, Vol. A26, P. 521-524.
30. Nowotny H., Jeitschko W., Benesovsky F. Novel Complex Carbides and Nitrides and Their Relation to Phases of Hard Substances. Planseeber. Pulvermetall. 1964, Vol. 12, P. 31-43.
31. Mabuchi H., Tsuda H., Nakayama Y. Processing of TiAl-Ti2AlN Composites and their Compressive Properties. J. Mater. Res. 1992, Vol. 7. P. 894-900.
32. Jeitschko W., Nowotny H., Benesovsky F. Ti2AlN and Nitrogen Containing H-Phase. Monatsh. Chem. 1963, Vol. 94, P. 1198-1200.
33. Ivchenko V. I., Lesnaya M. I., Nemchenko V. F., Kosolapova T. Ya. Study of Preparation Conditions and Certain Physical Properties of the Ternary Compound TI2AlN. Poroshk. Metall. 1976, No. 4, P. 60-63.
34. Ivchenko V. I., Kosolapova T. Ya. Investigation of Abrasive Properties of Ternary Compounda in the Systems Ti-Al-C and Ti-Al-N. Poroshk. Metall. 1976, No. 8, P. 56-59.
35. Farber L., Levin I., Barsoum M. W., El-Raghy T., Tzenov T. High-Resolution Transmission Electron Microscopy of Some Tin+iAXn Compounds (n = 1, 2; A = Al or Si; X = C or N). J. Appl. Phys. 1990, Vol. 86, P. 2540-2543.
36. Magnan J., Weatherly G. C., Cheynet M.-C. The Nitriding Behavior of Ti-Al Alloys at 1000 °C. Metall. Mater. Trans. A. 1999, Vol. 30A, P. 19-29.
37. Gamarnik M. Y., Barsoum M. W., El-Raghy T. Improved X-Ray Powder Diffraction Data for Ti2AlN. Powder Diffr. 2000, Vol. 15, P. 241-242.
38. Barsoum M. W. The MN+1AXN phases: a new-class of solids; thermodinamically stable nanolaminates. Prog. Solid St. Chem. 2000, Vol. 28, P. 201-281.
39. Barsoum M. W., El-Raghy T., Radovic M. Ti3SiC2: a layered machinable ductile carbide. Interce-ram. 2000, Vol. 49, P. 226-233.
40. Kooi B. J. R., Poppen J., Carvalho N. J. M. Ti3SiC2: a damage tolerant ceramic studied with nanoin-dentations and transmission electron microscopy. Acta Mater. 2003, Vol. 51, P. 2859-2872.
41. Palmquist J.-P. Carbide and MAX-phase engineering by thin film synthesis. Comprehensive Summaries of Uppsala. Dissertations from the Faculty of Science and Technology. 2004, No. 930, 70 p.
42. Sun Z. M. Progress in research and development on MAX phases: a family of layered ternary Compounds. International Materials Reviews. 2011, Vol. 56, P. 143-167.
43. Khirsh P., Khovi A., Nikolson R. Elektronnaya mikroskopiya tonkikh kristallov [Electron microscopy of thin crystals]. Moscow, Mir Publ., 1968, 574 p.
44. Koneva N. A., Kozlov E. V. [The nature of substructure hardening]. Izvestiya VUZov. Fizika. 1982, No. 8, P. 3-14 (In Russ.).
45. Koneva N. A., Kozlov E. V., Trishkina L. I. [The long-range stress fields, curvature-torsion of the crystal lattice and the stage of plastic deformation. The Measurement methods and results]. Novyye metody v fizike i mekhanike deformiruyemogo tverdogo tela. Sbornik tru-dov mezhdunarodnoy konferentsii. Tomsk, TGU Publ., 1990, P. 83-93 (In Russ.).
46. Teplyakova L. A., Ignatenko L. N., Kasatkina N. F. [The Regularities of plastic deformation of steel with the structure of tempered martensite]. Plasticheskaya defor-matsiya splavov. Strukturno-neodnorodnyye materialy. Tomsk, TGU Publ., 1987, P. 26-51 (In Russ.).
47. Ivanov Yu. F., Gromov V. E., Popova N. A. Strukturno-fazovyye sostoyaniya i mekhanizmy uprochneniya deformirovannoy stali [The structural-phase state and strengthening mechanisms of deformed steel]. Novokuznetsk, Poligrafist Publ., 2016, 510 p.
Библиографические ссылки
1. Белов А. Ф., Бенедиктова Г. П., Висков А. С. Строение и свойства авиационных материалов. М. : Металлургия, 1989. 368 с.
2. Рахманкулов М. М. Металлургия стратегических металлов и сплавов. М. : Теплотехник, 2008. 504 с.
3. Калачев Б. А., Елагин В. И., Ливанов В. А. Металловедение и термическая обработка цветных металлов и сплавов. М. : МИСиС, 2005. 432 с.
4. Белецкий В. М., Кривов Г. А. Алюминиевые сплавы. Состав, свойства, технология, применение. Киев : КОМИНТЕХ, 2005. 365 с.
5. Электронно-ионно-плазменная модификация поверхности цветных металлов и сплавов / под ред. Н. Н. Коваля, Ю. Ф. Иванова. Томск : НТЛ, 2016. 312 с.
6. Коваль Н. Н., Иванов Ю. Ф. Эволюция структуры поверхностного слоя стали, подвергнутой электронно-ионно-плазменным методам обработки. Томск : НТЛ, 2016. 304 с.
7. Грибков В. А., Григорьев Ф. И., Калин Б. А. Перспективные радиационно-пучковые технологии обработки материалов. М. : Круглый стол, 2001. 528 с.
8. Кадыржанов К. К., Комаров Ф. Ф., Погребняк А. Д. Ионно-лучевая и ионно-плазменная модификация материалов. М. : МГУ, 2005. 640 с.
9. Поут Дж. М., Фоти Г., Джекобсон Д. К. Модификация и легирование поверхности лазерными, ионными и электронными пучками. М. : Машиностроение, 1987. 424 с.
10. Громов В. Е., Иванов Ю. Ф. Структура, фазовый состав и свойства титана после комплексных упрочняющих технологий. Новокузнецк : СибГИУ, 2015. 304 с.
11. Шулов В. А., Пайкин А. Г., Новиков А. С. Сильноточные электронные импульсные пучки для авиационного двигателестроения. М. : Артек, 2012.
12. Модификация материалов компрессионными плазменными потоками / В. В. Углов [и др.]. Минск : БГУ, 2013. 248 с.
13. Модификация структуры и свойств эвтектического силумина электронно-ионно-плазменной обработкой / А. П. Ласковнев [и др.]. Минск : Беларус. Навука, 2013. 287 с.
14. ГОСТ 11069-2001. Алюминий первичный. Марки. Межгосударственный совет по стандартизации, метрологии и сертификации. Минск, 2001.
15. Лякишев Н. П. Диаграммы состояния двойных металлических систем : справ. В 3 т. М. : Машиностроение. 1996. Т. 1. С. 992.
16. Лякишев Н. П. Диаграммы состояния двойных металлических систем : справ. В 3 т. М. : Машиностроение. 1996. Т. 3. С. 872.
17. Lengauer W., Ettmayer P. The Crystal Structure of a New Phase in the Titanium-Nitrogen System // J. Less-Common Met. 1986. Vol. 120. P. 153-159.
18. Rogl P., Schuster J. C. Ti-B-N (Titanium - Boron - Nitrogen) in Phase Diagrams of Ternary Boron Nitride and Silicon Nitride Systems // Materials Park, Ohio: Materials Informations Soc. 1992. P. 103-106.
19. Lengauer W. The Crystal Structure of n-Ti3N2_x: An Additional New Phase in the Ti-N System // J. Less-Common Met. 1986. Vol. 125. P. 127-134.
20. Durlu N., Gruber U., Pietzka M. A. Phases and Phase Equilibria in the Quaternary System Ti-Cu-Al-N at 850 °C // Z. Metallkd. 1997. Vol. 97. P. 390-400.
21. Procopio A. T., El-Raghy T., Barsoum M. W. Synthesis of Ti4AlN3 and Phase Equilibria in the Ti-Al-N System // Metall. Mater. Trans. 2000. Vol. 31 A. P. 373-378.
22. Schuster J. C., Bauer, J. The Ternary System Titanium-Aluminium-Nitrogen // J. Solid State Chem. 1984. Vol. 53. P. 260-265.
23. Schuster J. C., Bauer J., Nowotny H. Applications to Materials Science of Phase Diagrams and Crystal Structures in the Ternary Systems Transition Metal-Aluminium-Nitrogen // Rev. Chim. Miner. 1985. Vol. 22. P. 546-554.
24. Barsoum M. W., Ali M., El-Raghy T. Processing and Characterization of Ti2AlC, Ti2AlN and Ti2AlC0.5N0.5 // Metall. Trans. 2000. Vol. A 31A. P. 1857-1865.
25. Barsoum M. W. Rawn C. J., El-Raghy T., Pro-copio A. T., Porter W. D., Wang H., Hubbard C.R. Thermal Properties of Ti4AlN3 // J. Appl. Phys. 2000. Vol. 87. P. 8407-8414.
26. Interfacial Reactions in Epitaxial Al/Tii-xAlxN (0 < x < 0.2) Model Diffusion-Barrier Structure / I. Petrov [et al.] // J. Vac. Sci. Technol. 1993. Vol. A11. P. 11-17.
27. Strusture and Properties of (Tii-xAlx)N Films Prepared by Reactive Sputtering / Y. Tanaka [et al.] // Thin Solid Films. 1993. Vol. 228. P. 238-241.
28. Ikeda T., Satoh H. Phase Formation and Characterization of Hard Coatings in the Ti-Al-N System Prepared by the Cathodic Arc Ion Platting Method // Thin Solid Films. 1991. Vol. 195. P. 99-110.
29. Wu Z. L., Pope D. P., Vitek V. Ti2NAl in L12 Al3Ti-Base Alloys // Metall. Mater. Trans. 1995. Vol. A26. P. 521-524.
30. Nowotny H., Jeitschko W., Benesovsky F. Novel Complex Carbides and Nitrides and Their Relation to Phases of Hard Substances // Planseeber. Pulvermetall. 1964. Vol. 12. P. 31-43.
31. Mabuchi H., Tsuda H., Nakayama Y. Processing of TiAl-Ti2AlN Composites and their Compressive Properties // J. Mater. Res. 1992. Vol. 7. P. 894-900.
32. Jeitschko W., Nowotny H., Benesovsky F. Ti2AlN and Nitrogen Containing H-Phase // Monatsh. Chem. 1963. Vol. 94. P. 1198-1200.
33. Ivchenko V. I., Lesnaya M. I., Nemchenko V. F., Kosolapova T. Ya. Study of Preparation Conditions and Certain Physical Properties of the Ternary Compound TI2AlN // Poroshk. Metall. 1976. No. 4. P. 60-63.
34. Ivchenko V. I., Kosolapova T. Ya. Investigation of Abrasive Properties of Ternary Compounda in the Systems Ti-Al-C and Ti-Al-N // Poroshk. Metall. 1976. №. 8. P. 56-59.
35. High-Resolution Transmission Electron Microscopy of Some Tin+iAXn Compounds (n = 1, 2; A = Al or Si; X = C or N) / L. Farber [et al.] // J. Appl. Phys. 1990. Vol. 86. P. 2540-2543.
36. Magnan J., Weatherly G. C., Cheynet M.-C. The Nitriding Behavior of Ti-Al Alloys at 1000°C // Metall. Mater. Trans. A. 1999. Vol. 30A. P. 19-29.
37. Gamarnik M. Y., Barsoum M. W., El-Raghy T. Improved X-Ray Powder Diffraction Data for Ti2AlN // Powder Diffr. 2000. Vol. 1. P. 241-242.
38. Barsoum M. W. The MN+1AXN phases: a new-class of solids; thermodinamically stable nanolaminates // Prog. Solid St. Chem. 2000. Vol. 28. P. 201-281.
39. Barsoum V. W., El-Raghy T., Radovic M. Ti3SiC2: a layered machinable ductile carbide // Interce-ram. 2000. Vol. 49. P. 226-233.
40. Kooi B. J., Poppen R. J., Carvalho N. J. M. Ti3SiC2: a damage tolerant ceramic studied with nanoin-dentations and transmission electron microscopy // Acta Mater. 2003. Vol. 51. P. 2859-2872.
41. Palmquist J-P. Carbide and MAX-phase engineering by thin film synthesis // Comprehensive Summaries of Uppsala. Dissertations from the Faculty of Science and Technology. 2004. No. 930. 70 p.
42. Sun Z. M. Progress in research and development on MAX phases: a family of layered ternary Compounds // International Materials Reviews. 2011. Vol. 56, No. 3. Р. 143-167.
43. Хирш П., Хови А., Николсон Р. Электронная микроскопия тонких кристаллов. М. : Мир, 1968. 574 с.
44. Конева Н. А., Козлов Э. В. Природа субструктурного упрочнения // Известия вузов. Физика. 1982. № 8. С. 3-14.
45. Конева Н. А., Козлов Э. В., Тришкина Л. И. Дальнодействующие поля напряжений, кривизна-кручение кристаллической решетки и стадии пластической деформации. Методы измерений и результаты // Новые методы в физике и механике деформируемого твердого тела : сб. тр. междунар. конф. Томск : ТГУ, 1990. С. 83-93.
46. Теплякова Л. А., Игнатенко Л. Н., Касаткина Н. Ф. Закономерности пластической деформации
стали со структурой отпущенного мартенсита // Пластическая деформация сплавов. Структурно-неоднородные материалы. Томск : ТГУ, 1987. С. 26-51.
47. Иванов Ю. Ф., Громов В. Е., Попова Н. А. Структурно-фазовые состояния и механизмы упроч-
нения деформированной стали. Новокузнецк : Полиграфист, 2016. 510 с.
© Ivanov Yu. F., Eresko S. P., Ahmadeev Yu. H., Lopatin I. V., Klopotov А. А., 2019
Ivanov Yurii Fedorovich - Dr. Sc., assistant professor, senior scientist, Institute of High Current Electronics of the SB RAS. E-mail: [email protected].
Eresko Sergei Pavlovich - Dr. Sc., professor, Corresponding member of Academy of Higher Education of the Russian Federation, honored inventor of the Russian Federation, Department of Fundamentals of machine design, Institute of Mechanical Engineering and Mechatronics, Reshetnev Siberian State University of Science and Technology. E-mail: [email protected], [email protected].
Ahmadeev Yurii Halatovych - Cand. Sc., senior researcher, Institute of High Current Electronics of the SB RAS. E-mail: [email protected].
Lopatin Ilya Viktorovich - Cand. Sc., scientist, Institute of High Current Electronics of the SB RAS. E-mail: [email protected].
Klopotov Anatoly Anatolyevich - Dr. Sc., professor, Tomsk State University of Architecture and Building. E-mail: [email protected].
Иванов Юрий Федорович - доктор физико-математических наук, доцент, главный научный сотрудник лаборатории плазменной эмиссионной электроники, Институт сильноточной электроники СО РАН. E-mail: [email protected] .
Ереско Сергей Павлович - доктор технических наук, заслуженный изобретатель Российской Федерации, член-корреспондент Академии наук ВШ РФ, профессор, профессор кафедры основ конструирования машин, Сибирский государственный университет науки и технологий имени академика М. Ф. Решетнева. E-mail: [email protected].
Ахмадеев Юрий Халяфович - кандидат технических наук, старший научный сотрудник лаборатории плазменной эмиссионной электроники, Институт сильноточной электроники СО РАН. E-mail: [email protected].
Лопатин Илья Викторович - кандидат технических наук, научный сотрудник лаборатории плазменной эмиссионной электроники, Институт сильноточной электроники СО РАН. E-mail: [email protected].
Клопотов Анатолий Анатольевич - доктор физико-математических наук, профессор, Томский государственного архитектурно-строительного университета. E-mail: [email protected].
